Крышные EC-вентиляторы DVCI-POC

Casing

Casing made from sea water resistant aluminium. Base frame manufactured from galvanised steel. DVCI-POC with 50 mm mineral wool acoustic and thermal insulation.

Motor

Energy-saving, highly efficient EC external rotor motors.

Impeller geometry

Radial impeller with backward curved blades.

Output control

100 % controllable.

DVC(I)-POC with integrated pressure regulator and temperature sensor for external temperature compensation.

The programming for constant pressure control can be executed with and without external temperature compensation.

Motor protection

The motor protection is integrated in the motor electronics.

Integrated pressure sensor

Temperature sensor for outdoor temperature compensation

Multipurpose LC display and keyboard

100 % speed controllable

Integrated motor protection

Safe and maintenance free operation

Energy-saving

Sizes 315 up to 500 inclusive tilting device

Alarm relay(2A, 250VAC)

Two RS-485 interfaces for networking via MODBUS RTU

The DVCI-POC roof fans are driven by EC- external rotor motors, so called energy saving motors with high efficiency. The input voltage for single phase units can vary between 200 and 277V, for three phase units between 380 and 480V. All motors are suitable for 50Hz and 60Hz and from size 355 up to 710 suspended on effective vibration dampers. Motor protection is integrated in the electronics of the motor, no additional external motor protection device is needed.

The DVCI-POC versions have integrated pressure sensors and temperature sensor for outdoor temperature compensation. The electronics could be programmed for a pressure constant operation or pressure constant operation with outdoor temperature compensation. The factory setting is pressure constant operation with outdoor temperature compensation. All set point adjustments over the keyboard and all values were shown on the LC display. The purpose of the controller is to reach and maintain the target values set. To accomplish this, the measured actual value (sensor value) is compared with the adjusted target value, and the controlled value (modulation) is deduced from this. Controlled output of the controller is 0 - 10 V.

The casing is made from seawater-resistant aluminum,

soundproofed with 50mm mineral wool.

Base frame from galvanised steel. Backward curved impellers manufactured from polypropylen PP for size 315-710.


Технические характеристики:

Наименование Напряжение (номинальное) Частота Количество фаз Потребляемая мощность Потребляемый ток
DVCI 560D-POC EC 400 В 50, 60 Hz 3~ 2 753 Вт 4,13 A
DVCI 630D-POC EC 400 В 50, 60 Hz 3~ 3 330 Вт 4,96 A
DVCI 710D-POC EC 400 В 50, 60 Hz 3~ 2 938 Вт 4,32 A

Наименование Скорость вращения рабочего колеса Расход воздуха Температура перемещаемого воздуха Макс. температура перемещаемого воздуха, при регулровании скорости Уровень звукового давления на 10 м (свободное поле)
DVCI 560D-POC EC 1 706 об/мин макс. 11 153 м³/ч макс. 60 °C 60 °C
DVCI 630D-POC EC 1 678 об/мин макс. 13 882 м³/ч макс. 55 °C 55 °C
DVCI 710D-POC EC 1 306 об/мин макс. 16 484 м³/ч макс. 55 °C 55 °C 46 дБ(А)

Наименование Уровень звукового давления на 4 м (свободное поле) Класс защиты, двигатель Класс изоляции Соответствие ErP Вес
DVCI 560D-POC EC IP55 F ErP 2018 84 кг
DVCI 630D-POC EC IP55 F ErP 2018 89 кг
DVCI 710D-POC EC 54 дБ(А) IP55 F ErP 2016, ErP 2018 115 кг

Наименование Тип двигателя Цена, руб
DVCI 560D-POC EC EC 476
DVCI 630D-POC EC EC 552
DVCI 710D-POC EC EC 538


Закрыть
Распечатано с сайта Вентснаб М , (495) 225-58-52